LDL Calculator
Calculate LDL cholesterol from a standard lipid panel: total cholesterol, HDL cholesterol and triglycerides, in mg/dL or mmol/L. This LDL calculator shows two published equations side by side — the classic Friedewald equation and the newer NIH equation (Sampson) — and the category each result falls in under the National Cholesterol Education Program guidelines.
For information only — not medical advice.
How to use
- Choose the units of your lab report: mg/dL (used in the US) or mmol/L.
- Enter total cholesterol, HDL cholesterol and triglycerides from the same blood test.
- Read the LDL by each equation and its category under the form.
Example: with total cholesterol of 200 mg/dL, HDL of 50 mg/dL and triglycerides of 150 mg/dL, the Friedewald equation gives an LDL of 120 mg/dL and the NIH equation gives 123 mg/dL[1][2]. Both fall in the near optimal category[3].
How it is calculated
Most labs do not measure LDL directly: they measure total cholesterol, HDL and triglycerides and calculate LDL from them. Both equations subtract HDL and the cholesterol carried by triglyceride-rich particles (VLDL) from total cholesterol. They differ in how they estimate the VLDL part:
- Friedewald (1972) takes it as triglycerides divided by 5, in mg/dL[1]. It was checked against LDL measured with an ultracentrifuge and is meant for triglycerides below 400 mg/dL[1].
- NIH equation (Sampson, 2020) lets the share depend on triglycerides and non-HDL cholesterol[2]. It was built on LDL measured by ultracentrifugation at the National Institutes of Health and works for triglycerides up to 800 mg/dL[2].
- Friedewald equation (triglycerides under 400 mg/dL)
- LDL = total cholesterol − HDL − triglycerides ÷ 5 (all in mg/dL)
- NIH equation (triglycerides up to 800 mg/dL)
- LDL = TC ÷ 0.948 − HDL ÷ 0.971 − (TG ÷ 8.56 + TG × non-HDL ÷ 2140 − TG² ÷ 16100) − 9.44
- TC — total cholesterol, TG — triglycerides, non-HDL = TC − HDL; all in mg/dL
- mmol/L and mg/dL
- Cholesterol: 1 mmol/L = 38.67 mg/dL
- Triglycerides: 1 mmol/L = 88.57 mg/dL
- Values in mmol/L are converted to mg/dL, calculated, and converted back, so both unit systems give the same LDL
- Laboratories that work in mmol/L often write the Friedewald equation as TC − HDL − TG ÷ 2.2; the result differs by up to about 0.02 mmol/L
What the result means
The calculator shows the category of each result under the Adult Treatment Panel III (ATP III) of the National Cholesterol Education Program[3]:
- Optimal: below 100 mg/dL (2.59 mmol/L)[3].
- Near optimal or above optimal: 100 to 129 mg/dL (2.59 to 3.35 mmol/L)[3].
- Borderline high: 130 to 159 mg/dL (3.36 to 4.13 mmol/L)[3].
- High: 160 to 189 mg/dL (4.14 to 4.90 mmol/L)[3].
- Very high: 190 mg/dL (4.91 mmol/L) or higher[3].
The cut-points in mmol/L are the mg/dL values converted with the factor shown above. The category is read from the number shown, in the units you chose. A personal LDL goal depends on your overall risk of heart disease, and a doctor sets it.
Limits
- With triglycerides of 400 mg/dL (4.52 mmol/L) or more, the Friedewald equation is not used, and the calculator shows only the NIH result[1][2].
- Above 800 mg/dL (9.03 mmol/L) of triglycerides, neither equation applies; LDL then needs a direct lab test[2].
- The Friedewald equation is less accurate when triglycerides are high or LDL is low; the NIH equation was designed to do better in these cases[2].
- The Friedewald method does not apply when the blood contains chylomicrons or in type III hyperlipoproteinemia[1].
- A calculated LDL is an estimate. It does not diagnose a lipid disorder or tell you whether you need treatment.
Frequently asked questions
Which LDL equation is more accurate?
In the NIH study, the NIH equation was closer to LDL measured by ultracentrifugation than the Friedewald equation, especially when triglycerides were high or LDL was low[2].
Why do the two equations give different LDL values?
They estimate the cholesterol in triglyceride-rich particles differently. Friedewald divides triglycerides by a fixed 5; the NIH equation changes the share with the levels of triglycerides and non-HDL cholesterol[1][2].
What is a normal LDL level?
ATP III calls LDL below 100 mg/dL (2.59 mmol/L) optimal[3]. The goal for you depends on your overall heart risk, which a doctor assesses.
Can I use results in mmol/L?
Yes. Choose mmol/L, and the calculator converts the values to mg/dL, calculates, and converts the result back, so both unit systems give the same LDL.
Sources
- Friedewald et al., 1972. Estimation of the Concentration of Low-Density Lipoprotein Cholesterol in Plasma, Without Use of the Preparative Ultracentrifuge. Clin Chem. doi:10.1093/clinchem/18.6.499
- Sampson et al., 2020. A New Equation for Calculation of Low-Density Lipoprotein Cholesterol in Patients With Normolipidemia and/or Hypertriglyceridemia. JAMA Cardiol. doi:10.1001/jamacardio.2020.0013
- NCEP ATP III, 2001. Executive Summary of the Third Report of the National Cholesterol Education Program (NCEP) Expert Panel on Detection, Evaluation, and Treatment of High Blood Cholesterol in Adults (Adult Treatment Panel III). JAMA. doi:10.1001/jama.285.19.2486